ANALISA MANAJEMEN RESIKO DENGAN METODE FAULT THREE ANALISYS (FTA) SYSTEM COMPRESSOR AIR MINUM DALAM KEMASAN PT. SWABINA GATRA

Rizky Adi Kurniawan

Sari


Occupational safety and health is now starting to be important for the wider community in Indonesia, especially for employees and industrial workers, considering the growing economy and industry as well as general development, the greater the potential for harm caused. Actually this problem can be overcome by applying existing methods such as Fault Three Analysis (FTA). The purpose of this research is to carry out risk management on work equipment system failures as an effort to control work accidents at PT. Swabina Gatra The design of this research is descriptive. Hazard identification in this research uses the (HIRARC) method then the hazard result with the highest value is used as the Top Event in the Fault Three Analysis (FTA) method. The implementation stage of this method is to identify the potential and overcome hazards in the Compressor System Unit for Bottled Drinking Water PT. Swabina Gatra. The results showed that there were 7 cut-sets or causes of failure in the compressor system. The cut-set results obtained by the prevention stage which are enforced are the provision of Earth-Leakage Circuit Breakers (ELCB) on the electric panel compressor system, Perform periodic pressure vessel calibration tests no later than once every 5 years, Work in accordance with SOPs or work instructions that have been set by the Company , and conduct periodic inspections or inspections and schedule repairs and maintenance.


Kata Kunci


Fault three analisys, FTA

Teks Lengkap:

PDF

Referensi


Afredo, L. W., & Tarigan, U. P. (2021). Analisis Resiko Kecelakaan Kerja di CV. Jati Jepara Furniture dengan Metode HIRARC (Hazard Identification Risk Assessment and Risk Control). JURITI PRIMA (Junal Ilmiah Teknik Industri Prima), 30–37

Disnakertrans Provinsi Banten. (2022). Disnakertrans Provinsi Banten. Dipetik maret rabu, 2022, dari Disnakertrans Provinsi Banten: https://disnakertrans.bantenprov.go.id/Berita/topic/288

Djamal, N., & Azizi, R. (2015). IDENTIFIKASI DAN RENCANA PERBAIKAN PENYEBAB DELAY PRODUKSI. Jurnal Intech Teknik Industri, 34-45.

Dr. Antonius Alijoyo, C. Q., Bobby Wijaya, M. E., & Intan Jacob, M. (2021). 31 TEKNIK PENILAIAN RISIKO BERBASIS ISO 31010 : Fault Tree Analysis. CRMS.

Dr. Suma'mur. P.KM.M.S.C. (1996). Hiegene Perusahaan Dan Kesehatan Kerja. Jakarta: PT. Toko Gunung Agung.

Dwisetiono, & Fairussihan, J. D. (2022). Analisis Risiko Keselamatan Dan Kesehatan Kerja ( K3 ) Pada Proses Perbaikan Kapal di PT. Dock Dan Perkapalan Surabaya Menggunakan Metode HIRARC (Hazard Identification, Risk Assessment, And Risk Control). HEXAGON: Jurnal Teknik Dan Sains, 0–16.

Giananta, P. H. (2020). Analisa Potensi Bahaya Dan Perbaikan Sistem Keselamatan dan Kesehatan Kerja Menggunakan Metode HIRARC Di PT. Boma Bisma Indra. Jurnal Valtech (Jurnal Mahasiswa Teknik Industri), 106–110.

International Labor Organization. (2022, maret senin). Safety And Health At Work. Dipetik maret senin, 2022, dari International Labor Organization: https://www.ilo.org/global/topics/safety-and-health-at-work/lang--en/index.htm

Kementrian Ketenagakerjaan Republik Indonesia. (2022). JDIH Kementrian Ketenagakerjaan Republik Indonesia. Dipetik maret senin, 2022, dari JDIH Kementrian Ketenagakerjaan Republik Indonesia: https://jdih.kemnaker.go.id/katalog-1429-Peraturan%20Menteri.html

License, Standard Australia. (2004). AS/NZS 4360:2004 Risk managementin Security Risk Analysis. Dalam S. A. License. Brisbane: ISMCPI.

Lienetic Jaya. (2018). apa-itu-elcb. Dipetik maret kamis, 2022, dari Lienetic Jaya: https://lieneticjaya.com/apa-itu-elcb/

Mumtazi, A. N., & Putra, B. M. (2020). Analisis Penyebab Keterlambatan Pengadaan Komponen pada Sistem Repair Order Proyek Engine CFM56-7B ESN. Seminar dan Konferensi Nasional IDEC 2020, B10.1-B10.10.

Referensi Standar. (2022). Referensi Standar. Dipetik maret 22, 2022, dari Referensi Standar: https://standarku.com/fault-tree-analysis/

Saputro, T., & Lombardo, D. (2021). Metode Hazard Identification, Risk Assessment And Determining Control (HIRADC) DalamMengendalikan Risiko Di PT. Zae Elang Perkasa. Jurnal Baut Dan Manufaktur, 23–29.

Satriyo, B., & Puspitasari, D. (2017). Analisis Pengendalian Kualitas Dengan Menggunakan Metode Fault Tree Analysis Untuk Meminimumkan Cacat Pada Crank Bed Di Lini Painting PT. Sarandi Karya Nugraha. Neliti.

Trisaid, S. N. (2020). Analisis Risiko Kecelakaan Kerja Pada Kegiatan Rig Service Menggunakan Metode Hirarc Dengan Pendekatan Fta. Jurnal Ilmiah Teknik Industri, 25–33.

Triswandana, I. W. (2020). Penilaian Risiko K3 dengan Metode HIRARC. UKaRsT: Universitas Kadiri Riset Teknik Sipil, 97–108.

Wahyu, N. P., & Fathoni, M. Z. (2018). Analisis Penyebab Kecacatan Produk Bordir Komputer Menggunakan Metode Fault Tree Analysis (FTA) dan Failure Mode and Effect Analysis (FMEA)(Studi Kasus: Cv. Batari, Gresik). Matrik.




DOI: http://dx.doi.org/10.55445/teknovasi.v9i1.657

Article Metrics

Sari view : 0 | PDF : 0

Refbacks

  • Saat ini tidak ada refbacks.


Creative Commons License This journal is licensed under a Creative Commons Attribution 4.0 International License